(In stock) Morandi powder series | Eagle claw small round three-color irregular Cement succulent plant

https://live.staticflickr.com/65535/51289636646_0b17a2f081_o.jpg 🔥🔥🔥Hot-selling products with a fever have more in stock and are randomly planted and shipped, not one item at a time. If you really mind the planting status, you can private message the designer to ask for photos🔥🔥🔥 Eagle claw, a succulent plant of the Liliaceae sclerophyll genus, has sharp-shaped leaves like eagle claws, compactly arranged leaf tips, small white warts, and is resistant to shade and drought. It is an ideal interior decoration. Eagle Claws are very similar to Twelve Hard Leaves, they also have eagle claw-like plants, vigorous and powerful, but Eagle Claws don't look as hard as Twelve Hard Leaves, and the color is much more emerald green than Twelve Hard Leaves. It likes a warm, dry and sunny environment, and is afraid of low temperature and humidity. It is easy to maintain and can grow in insufficient sunlight. Please avoid overwatering. Soil that is too wet may cause rot. In spring and autumn, if the watering frequency is increased appropriately, it will grow rapidly. In hot summer, it is semi-dormant at high temperature, so the frequency of watering should be reduced, and it should be watered less in winter, and placed in a warm room facing south. ｜Light｜ It likes sufficient scattered light, avoid direct sunlight and pay attention to ventilation during high temperature season in summer. It should be noted that although it is tolerant to shade, it cannot be completely without light. If the shade is too long, the plants will deform and grow leggy. Once the leggy grows, it will take a long time to grow back. ｜Temperature｜ Not cold-resistant, the optimum temperature for growth is 15-25 degrees, the lowest temperature is not lower than 10 degrees, and it enters a dormant state above 30 degrees. ｜Watering｜ Watering should be mastered "Never dry or water, water thoroughly", avoid water accumulation, otherwise the roots will rot; also do not lack water for a long time, so as not to dry out the leaves, water it thoroughly in the spring and autumn growth period, about once a week, and in summer Water a little about once every two weeks, and water again when it dries out in winter. The actual glue frequency can be adjusted according to your planting environment. ｜Summer dormancy｜ During the dormancy period in summer, because the temperature is too high, the plants basically slow down or stop growing, and the bottom leaves sometimes dry up a little. Keep the pot soil moderately dry throughout the summer, and give some water to the side of the pot every month. The eagle claws are not easy to rot and are very strong. Usually, keep the water needed for the slow root system or stop growth of the plant. It cannot be said that it will go dormant without water because of the high temperature. Yes, it will take a long time to wake up like that. During the dormant period, it is easy to consume the water and nutrients of some leaves, and the bottom and even the whole plant leaves will shrivel. In summer, due to slow growth and high temperature, the leaves of the whole plant basically do not see much growth. ｜Reproduction｜ Commonly used ramets, cuttings and seeding propagation, ramets can be combined with changing pots, all year round, often when changing pots in April-May, peel off the young plants around the mother plant, pot them directly, and place the ramets in pots Place the pot in a shaded place, and control watering, and gradually increase the amount of light and watering after new roots grow. ｜Blossom｜ The flowering period of the plant is spring and summer, with racemes. Pollination must be different plants, but also cross pollination between the same genus. If the flower branch is not pollinated, the flower stalk can be cut off, otherwise the flower spike will consume the nutrition of the plant. 📝Small key points for marking: tolerance to shade and drought, place with astigmatism, pay attention to ventilation, water not dry or water, water thoroughly, water about once a week 📏📏📏📏📏📏📏📏📏 Thickened small round basin size Diameter 7.2cm x height 4cm The inner size of the basin is 5cm in diameter 📏📏📏📏📏📏📏📏📏 The low-saturation Morandi color powder is mixed with white gray to increase the overall brightness, forming a three-color mix and match style, which is lively, playful and cute! Suitable for planting some cute, tender or furry little succulents! Cement hand-made texture, unique gradient three-color design, hand-made, creating a sense of irregularity in each pot, each of which looks different! It can also be used with a round chassis or an oval chassis, so you don't have to worry about water leaking everywhere! (The oval base can hold two round pots, as shown in the last picture) This type of plant has been planted for you, and it will be packaged as properly as possible for shipment, and a fragile product sticker will be attached. If there is a normal phenomenon of paving Stone, soil medium falling or plant loosening during transportation, brother freight driver It is unavoidable for a lot of goods to have a slight collision during delivery, please help us plant them gently after receiving the goods! ⭕️There are also hexagonal, round, square, oval and other different-shaped chassis that can be purchased separately for use. Watering thoroughly is not afraid of leaking everywhere! (The chassis color is preset to white-gray gradient color, if you have customized requirements on color, please write to us first.) ⭕️If the product you ordered is in stock, we will quickly pack and ship it for you. If the stock is insufficient, we will confirm the order with you and start production. After placing the order, please help us pay attention to whether there is a private message by letter! Thanks again! (If you need to reconfirm the physical photos of the spot, you can ask for photos by private message ✉️) ⭕️According to your needs, we can specially prepare and customize the color for you🎨 (If you need it, you can write to ask whether it can be made, and then place an order and increase the price to purchase customized services.) ⚠️Special customization needs about 5-7 days for mold filling, air drying, demoulding, and modification. Please do not place an order for customization if you need it urgently. You can only place an order for the stock in stock ⚠️Note: It is purely hand-made, and there will inevitably be some air bubbles and holes due to the characteristics of Cement. Each pot has unique textures, textures, pores and appearance that do not affect the structure. For us, it is part of the design. If you mind very much If the appearance of each Cement work is different, please consider carefully or write to inquire before placing an order. Returns and exchanges will not be accepted after the product is sold, thank you! ⚠️If the inventory is sufficient, you can private message to ask for photos, and choose your favorite style from many Cement works.